Battery review · Home Battery 400V (BAT-10K1P)
SolarEdge Home Battery 400V review
By CompareVolt · Updated · Last full check

CompareVolt rating
6.9 out of 10
Older model · availability not confirmed
A tidy add-on for a listed SolarEdge inverter, but only a single-phase Home Hub can give backup.
6.9 out of 10
- Warranty10 yrs, unlimited home; stay online
- Functionality9.7 kWh, 5 kW DC; backup is extra
- VPP readiness4 programs; only 1 names the 400V
- Australian backingSince 2013; on-site labour excluded
How this score adds up
| Warranty 7.0 (30%) | |
|---|---|
| Term: 10 years | 2.0 of 3 |
| Keeps 70% at year 10 | 1.5 of 2 |
| Home use: unlimited cycles | 3.0 of 3 |
| Conditions: needs portal link; can start 12 months after shipment; 0–40°C for 95% of term | 0.5 of 2 |
| Functionality 6.5 (35%) | |
| Power and backup 6.5 · 60% of Functionality | |
| Continuous power: 5 kW battery DC; the inverter sets AC output | 2.5 of 4 |
| Backup equipment: needs a single-phase Home Hub and Backup Interface | 1.0 of 2 |
| Backup output: set by the inverter | 1.0 of 2 |
| Three-phase homes: listed with the SExK-AUB three-phase inverter; one battery, no backup | 2.0 of 2 |
| Capacity and expansion 6.0 · 30% of Functionality | |
| Largest documented system: 9.7 kWh (one battery scored; up to 3 per Home Hub or Genesis inverter) | 1.0 of 4 |
| Adding later: whole batteries, up to 3 on Home Hub or Genesis; 1 on SExK-AUB | 3.0 of 4 |
| Usable figure: 9.7 kWh, agreed | 2.0 of 2 |
| Enclosure 7.0 · 10% of Functionality | |
| Enclosure rating: IP55 | 7.0 of 10 |
| 6.5 × 60% + 6.0 × 30% + 7.0 × 10% = 6.4, rounded to the nearest half point: 6.5 | |
| VPP readiness 5.5 (15%) | |
| Open programs: 1 names Home Battery 400V, 3 list SolarEdge | 4.5 of 8 |
| Warranty room for VPP use: 2.68 MWh per kWh | 1.0 of 2 |
| Australian backing 8.5 (20%) | |
| Presence: SolarEdge Technologies (Australia) Pty Ltd, Melbourne | 3.0 of 3 |
| In Australia since 2013 | 2.0 of 2 |
| Claim route: you email SolarEdge support | 2.0 of 2 |
| Claim costs: return delivery paid; your freight and on-site labour excluded | 1.5 of 3 |
| Overall: 7.0 × 30% + 6.5 × 35% + 5.5 × 15% + 8.5 × 20% = 6.9 | |
Rubric 1.0 · scored 16 Nov 2026 · How we rate batteries · Source documents
Rated so far: 38 batteries, from 4.4 to 8.2. Compare similar batteries · Use the quote checklist
In a nutshell
What’s good
- Documented setup process. SolarEdge's Australian connection guide documents the battery wiring and self-test, and backup commissioning for the single-phase Home Hub.
- Up to three batteries. Single-phase Home Hub and Genesis designs can take three batteries per inverter; three-phase SExK-AUB has a one-battery limit.
- 9.7 kWh usable. At 100% depth of discharge in one battery, before inverter losses and any outage reserve.
1 more good point
- Ten-year warranty. December 2024 AU terms: 70% energy retention and unlimited cycles for defined standard solar uses, including backup.
What to watch
- No backup with SExK-AUB. The SExK-AUB residential three-phase inverter supports one battery but does not provide backup with it.
- Warranty conditions. The Australian warranty requires Monitoring Platform connectivity and limits third-party management throughput.
- SolarEdge inverters only. Works with the datasheet's compatible SolarEdge inverters (Home Genesis, Home Hub, SExK-AUB), not another brand.
2 more things to watch
- Backup needs extra equipment. Needs a single-phase Home Hub, Backup Interface and backup enabled at commissioning, not just the battery.
- Repair labour excluded. The warranty excludes on-site repair, removal and reinstallation labour costs unless SolarEdge agrees in writing.
Good fit for: Homes already using, or deliberately choosing, a compatible SolarEdge inverter and wanting storage within the same monitoring system.
Look elsewhere if: You want freedom to use another inverter brand, or expect an SExK-AUB three-phase inverter to provide blackout backup.
All specifications and notes
Capacity and power
| Usable capacity | 9.7 kWhUsable energy in the reviewed configuration. |
|---|---|
| Battery continuous output | 5 kW DCPer battery; temperature affects power. Backup peak is 7.5 kW for 10 seconds. Household AC output depends on the inverter. |
| Backup requirement | Home Hub + interfaceRequires a single-phase Home Hub, a Backup Interface and commissioned backup wiring. SExK-AUB provides storage without backup. |
| Verified AU warranty | 10 years, usage capDecember 2024 AU terms: 70% retention; third-party management capped at 26 MWh. Confirm the supplied revision and conditions below. |
Manufacturer’s figures
As stated in the manufacturer’s Australian datasheet. Only the IP rating feeds the score; the rest are shown for reference.
| IP rating | IP55The maker’s rating for dust and water getting in, which matters on an outdoor wall. |
|---|---|
| Weight | 121 kgWhether it can go on a wall, and how the installer has to handle it.One BAT-10K1P battery (p.2) |
| Dimensions | 790 × 1179 × 250 mm (W × H × D)Whether it fits the wall or cupboard where the installer plans to put it.One BAT-10K1P battery (p.2) |
| Operating temperature | −10°C to +50°C ambient (charging)Whether it suits a hot garage or an outdoor wall where you live.Warranty needs 0°C to +40°C for at least 95% of the period (p.2) |
| Noise | < 25 dBA at 1 mMatters if it sits near a bedroom or a neighbour’s window. |
| Round-trip efficiency | 94.5% peakHow much of the energy you store comes back out when you use it.Printed as “Peak Roundtrip Efficiency”; no conditions stated (p.2) |
More specifications
| Expansion | Up to 3 batteries per inverterWhole batteries only. With a SExK-AUB inverter, one battery and one inverter per site. |
|---|---|
| Compatible inverters | Home Genesis, Home Hub, SExK-AUBCheck the exact model and its expansion and backup limits. |
| Warranty start | Earlier of install or 12 months from shipmentInstallation as recorded in the Monitoring Portal. NSW batteries registered under the PDRS start at installation. |
| Warranty temperature | 0–40°C for 95% of the term−10–50°C for the remainder, under the normal terms. |
| Monitoring | Portal connection requiredAn approved SolarEdge inverter and Monitoring Platform connection are needed throughout; no numerical offline grace period is given. |
What the system needs
| One 400V battery | The reviewed capacity is one BAT-10K1P unit. The June 2026 Australian datasheet gives its part number as BAT-10K1PS0B-01. |
|---|---|
| Compatible SolarEdge inverter | The Australian datasheet lists Home Genesis, Home Hub and SExK-AUB inverters. Check the exact model and its expansion and backup limits. |
| Backup Interface and circuits | For backup, include the single-phase Home Hub, Backup Interface, metering and protected-load wiring. The installer must enable backup during commissioning. |
The Australian BAT-10K1P Home Battery 400V, with 9.7 kWh of usable storage, connects to a compatible SolarEdge inverter; the inverter and backup equipment determine the installed system's capabilities.
Capacity and power
The June 2026 Australian datasheet gives 9.7 kWh usable at 100% depth of discharge. That is the energy in one battery, before the inverter's losses and any reserve you keep for outages. The 5 kW continuous output and 7.5 kW ten-second backup peak are battery output on the DC side. The paired inverter sets the household AC limit, and temperature can reduce battery power.
You add capacity in whole batteries. The datasheet allows up to three per inverter, except with the SExK-AUB three-phase inverter, where it allows one battery and one inverter per site. Don't apply the three-battery figure to that pairing. Our rating scores one battery, the size this review covers.
Backup and installation
Backup needs a SolarEdge Backup Interface, which SolarEdge's Australian connection guide says works with the single-phase Home Hub inverter only. Your installer must connect the chosen circuits and turn backup on at commissioning; installing the battery alone isn't enough. The guide includes both full-home and selected-load designs, so ask which your quote supplies and which loads can run at the same time.
The same guide lists SolarEdge's residential three-phase inverters among those that can't provide backup. SolarEdge's Australian SExK-AUB FAQ also says that adding this battery gives no backup. Some earlier SolarEdge three-phase models can't accept it at all. Confirm the complete inverter part number before treating an existing SolarEdge system as battery-ready.
Wall or floor mounting is supported, with the floor stand bought separately. Wireless SolarEdge Home Network links battery and inverter; the inverter may need its matching plug-in. This local link doesn't replace the Monitoring Platform connection the warranty requires.
Warranty and ownership
SolarEdge's Australian warranty for the BAT-10K1P is the December 2024 revision. The June 2026 Australian datasheet links instead to SolarEdge's global Home Battery 400V warranty, revised April 2023. Its terms are the same, but it lacks the Australian Consumer Law section, the NSW scheme exceptions and the Australian importer, so ask for the Australian edition with your quote.
The Australian terms cover workmanship, materials and energy capacity for ten years, with 70% energy retention at the end. Standard solar use has unlimited cycles: self-consumption, time of use, backup and SolarEdge-managed services. Third-party management instead limits the battery warranty to 26 MWh of throughput. The warranty doesn't say which VPPs count as third-party management, so get written confirmation for your provider.
Working the warranty’s energy limits through at one full charge and discharge a day:
- Home use: no throughput limit.
- VPP and other uses: 26 MWh, about 2.68 MWh per usable kWh. At one full charge and discharge a day that is reached in about 7.3 years, before the 10-year term ends.
Cover runs from installation, as recorded in the Monitoring Portal, or from 12 months after SolarEdge ships the battery, whichever comes first. So a battery that sat in stock can start its ten years before it is installed. Batteries installed in NSW and registered under the Peak Demand Reduction Scheme start at installation instead. That exception doesn't make you eligible for the scheme.
The battery must stay connected to an approved SolarEdge inverter and the Monitoring Platform for the whole term. SolarEdge says it can't honour the warranty without the portal connection, and it gives no offline grace period. The air around it must also stay at 0–40°C for at least 95% of the term and −10–50°C otherwise. The datasheet's table gives −10 to +50°C for charging, and its footnote repeats this rule. Under the NSW scheme exception, −10–50°C applies throughout.
Cover can pass to a new owner if the battery stays where it was installed. On-site repair, removal and reinstallation labour isn't covered unless SolarEdge agrees in writing first. Ask who pays for a service visit. Your Australian Consumer Law rights apply on top.
Brand and Australian support
Support evidence checked 21 September 2026; warranty and ABR record re-read 16 November 2026. SolarEdge Technologies (Australia) Pty Ltd, based in Victoria, has been active since 27 August 2013. The warranty names that company, in Melbourne, as the battery's importer, with an Australian phone number. SolarEdge has operated globally since 2006.
To claim, you email SolarEdge support with a short description, the serial number and the receipt. SolarEdge may repair the battery on site or at its facility, replace it with an equivalent product, or give a credit note for lost capacity. If it wants the battery back, you pay to ship it. SolarEdge pays to deliver the repaired or replacement unit, and customs, in the countries its shipping coverage lists. Labour, travel, accommodation, removal and reinstallation aren't covered unless SolarEdge agrees in writing first. Australian Consumer Law rights apply separately.
SolarEdge publishes guidance for owners whose installer has closed: check your remaining cover, engage another installer, use its preferred-installer directory and, if you want, buy a SolarEdge system health report. That is a documented route, but it may add diagnosis or labour costs, and a new installer may not accept the job.
We found no long-term Australian study of the Home Battery 400V, so nothing we read shows how often it fails.
Price and alternatives
SolarEdge's Australian product page directs buyers to its distributor route and gives no installed price. Get the battery, inverter, Backup Interface, mounting, monitoring connection and switchboard work itemised. Ask for rebate figures separately, confirmed for your exact installation; a live product page doesn't confirm stock or eligibility.
If changing the inverter makes this quote unattractive, use the sonnenBatterie Evo review and BYD HVM 11.0 review to compare other complete installations. Apply the same storage, blackout-load and service-cost checks to each quote.
Who it suits
This battery suits a home that already has, or is choosing, a listed SolarEdge inverter and wants storage in the same app. Size the storage first with the battery size calculator. Then have an installer check your existing inverter's complete model number, firmware and monitoring connection. Ask them to mark which circuits will work in an outage and to show you the backup setting at handover.
Keep the supplied battery part number and the Australian warranty with your commissioning records. This review covers the BAT-10K1P in the June 2026 Australian datasheet (part number BAT-10K1PS0B-01), not SolarEdge's separate 48V battery. Before you join a VPP, have the provider confirm your exact inverter. Then get SolarEdge to say in writing whether the VPP counts as third-party management, which limits cover to 26 MWh.
How it compares
Other reviewed batteries closest to 9.7 kWh of usable capacity.
- Family reference imageAlphaESS SMILE-G3-BAT-10.1P reviewRated 7.9 out of 109.6 kWh usable2024 warranty, installs 1 Nov on: 10 years or ≈30 MWhOne difference: VPP readinessAlphaESS SMILE-G3-BAT-10.1P9.5Home Battery 400V (BAT-10K1P)5.5

- Neovolt BW-BAT-9.6P reviewRated 6.9 out of 109.6 kWh usableWarranty: 12 years, 70%One difference: WarrantyNeovolt BW-BAT-9.6P9.0Home Battery 400V (BAT-10K1P)7.0

- Family reference imageSAJ B2-10.0-HV1 reviewRated 5.9 out of 109.6 kWh usableCapacity warranty: 10 years or ≈29.4 MWhOne difference: Australian backingSAJ B2-10.0-HV16.0Home Battery 400V (BAT-10K1P)8.5

Questions people ask
Is the SolarEdge Home Battery 400V compatible with my inverter?
The Australian datasheet lists the Home Genesis, Home Hub and SExK-AUB inverters. Check the exact model and its expansion and backup limits before treating an existing SolarEdge system as battery-ready.
Does the SolarEdge Home Battery 400V give blackout backup?
Only with a single-phase Home Hub inverter, a Backup Interface and backup enabled at commissioning. The SExK-AUB three-phase inverter stores energy but gives no backup.
How long is the SolarEdge Home Battery 400V warranty?
Ten years with 70% energy retention under the December 2024 Australian terms, with unlimited cycles for standard solar use. Third-party battery management limits cover to 26 MWh of throughput, and a Monitoring Platform connection is required throughout.
Can I add more SolarEdge Home Battery 400V units later?
The datasheet allows up to three batteries per inverter, added as whole batteries. With a SExK-AUB inverter it allows only one battery and one inverter per site.
How much does the SolarEdge Home Battery 400V cost in Australia?
SolarEdge's Australian page directs buyers to its distributor route and publishes no installed price. Installed prices come from quotes that itemise the battery, inverter, Backup Interface, mounting, monitoring and switchboard work.
How long will 9.7 kWh last?
Divide 9.7 kWh by your average load: about 9.7 hours at 1 kW or 3.2 hours at 3 kW, before inverter losses and any reserve you keep for outages.
Before you accept a quote
SolarEdge doesn’t publish a price for this battery, so the installed price comes from your quotes.
- The quote names the BAT-10K1P part-number suffix and the compatible SolarEdge inverter, with its complete model number and firmware.
- It lists the Home Hub, Backup Interface, metering and protected circuits, and says whether backup is full-home or selected-load.
- Battery, inverter, Backup Interface, mounting, monitoring connection and switchboard work are itemised, with rebates shown separately.
- The applicable Australian warranty revision is attached, with how third-party battery control and your VPP are treated.
- It confirms the Monitoring Platform connection and who pays for a service visit.
Estimate the federal battery certificates for 9.7 kWh usable (opens in a new tab)
Check the model in your quote
Check that your quote names Home Battery 400V (BAT-10K1P) in the configuration this review covers.
Australian support and warranty claims
- Australian presence
- SolarEdge Technologies (Australia) Pty Ltd, Melbourne
- In Australia since
- 2013
- Where claims go
- You email SolarEdge support
- Claim costs
- Return delivery paid; your freight and on-site labour excluded
SolarEdge Australian contact details (opens in a new tab) · Warranty document (opens in a new tab) · Checked
VPPs that list SolarEdge Home Battery
Compare programsThese programs list the battery family. “Names Home Battery 400V” marks a program whose published list names this line. Your exact battery, inverter and address still need approval; inclusion does not confirm warranty cover. How VPPs work.
All programs shown require an electricity account with the provider. If you already use that retailer, a switch may not be needed; a particular plan may still be required. Credits are before electricity costs and any program fees.
4 listings · 1 recorded as naming Home Battery 400V · Program A–Z
| Provider | Program | Names Home Battery 400V | States listed | Reward snapshot | Last checked |
|---|---|---|---|---|---|
| ActewAGL | Battery Power Top-Up | Not recorded | ACT · south-east NSW | $240/year in bill credits | |
| AGL | AGL VPP | Not recorded | NSW · VIC · QLD · SA | Sign-up, ongoing and event credits SA ongoing credits conflict across published sources ($80 or $180 a year); AGL confirms your amount when you join. | |
| Amber | SmartShift | Not recorded | NSW · VIC · SA · ACT · QLD (Energex) | Variable wholesale export earnings | |
| Origin Energy | Loop · Battery Lite | Yes | NSW · SA · VIC · QLD · ACT | $1/kWh during VPP events |
ActewAGL
Battery Power Top-UpListed: ACT · south-east NSW
AGL
AGL VPPListed: NSW · VIC · QLD · SA
Amber
SmartShiftListed: NSW · VIC · SA · ACT · QLD (Energex)
Origin Energy
Loop · Battery LiteListed: NSW · SA · VIC · QLD · ACT
Names Home Battery 400V
Reward snapshots — open the program for all credits, tariffs and conditions.
Source documents
5 documents
The documents behind this rating. Where we keep a copy, it is unmodified and dated; check the manufacturer for the latest version. We work out the rating with a fixed rubric from these documents and our VPP data. No manufacturer pays for a score or sees one before it is published.
- SolarEdge — Limited Home Battery Warranty (BAT-10K1P), Australia, revised December 2024 (PDF, opens in a new tab)
PDF, 315 KB · Used for: Warranty, Australian backing
Retrieved from knowledge-center.solaredge.com
- SolarEdge — Solution Connection and Configuration Guide for Australia, version 6.0, May 2024 (PDF, opens in a new tab)
PDF, 4.4 MB · Used for: Functionality
Retrieved from knowledge-center.solaredge.com
- SolarEdge — Home Battery for Australia datasheet (BAT-10K1PS0B-01), DS-000014-AUS, 15 June 2026 (PDF, opens in a new tab)
PDF, 174 KB · Used for: Functionality, Manufacturer’s figures, Review source
Retrieved from knowledge-center.solaredge.com
- www.solaredge.com/aus/contact-us (opens in a new tab)
Used for: Australian backing
- abr.business.gov.au/ABN/View?abn=15165506712 (opens in a new tab)
Used for: Australian backing