Battery review · T-BAT H 5.8 V2
SolaX Triple Power T-BAT H 5.8 V2 review
By CompareVolt · Updated · Last full check

CompareVolt rating
5.9 out of 10
Older model · availability not confirmed
Modest storage for a single-phase SolaX X1 Hybrid, held back by 2.8 kW battery power.
5.9 out of 10
- Warranty10 yrs, capped by manufacture date
- Functionality5.1 kWh, low 2.8 kW DC; single-phase
- VPP readiness2 programs only; both list SolaX
- Australian backingSince 2018; partial claim costs
How this score adds up
| Warranty 7.0 (30%) | |
|---|---|
| Term: 10 years | 2.0 of 3 |
| Keeps 70% at year 10 | 1.5 of 2 |
| Home use: 6,000 cycles, 6.0 MWh per kWh | 2.5 of 3 |
| Conditions: ends 129 months after manufacture; 50°C limit, under the datasheet's 55°C | 1.0 of 2 |
| Functionality 5.0 (35%) | |
| Power and backup 3.5 · 60% of Functionality | |
| Continuous power: 2.8 kW battery DC; the inverter sets AC output | 0.5 of 4 |
| Backup equipment: needs a separate SolaX hybrid inverter | 1.0 of 2 |
| Backup output: set by the inverter | 1.0 of 2 |
| Three-phase homes: one master is below the X3 Hybrid minimum of two units | 1.0 of 2 |
| Capacity and expansion 7.0 · 30% of Functionality | |
| Largest documented system: 20.7 kWh (4 units on an X3 Hybrid; an X1 Hybrid takes 3, 15.5 kWh) | 3.0 of 4 |
| Adding later: after the first year, only with SolaX's consent; voltage levels must match | 2.0 of 4 |
| Usable figure: 5.1 kWh, on the archived Australian V2 datasheet | 2.0 of 2 |
| Enclosure 10.0 · 10% of Functionality | |
| Enclosure rating: IP65 | 10.0 of 10 |
| 3.5 × 60% + 7.0 × 30% + 10.0 × 10% = 5.2, rounded to the nearest half point: 5.0 | |
| VPP readiness 3.5 (15%) | |
| Open programs: 2 list SolaX | 2.0 of 8 |
| Warranty room for VPP use: 3.51 MWh per kWh | 1.5 of 2 |
| Australian backing 7.5 (20%) | |
| Presence: SolaX Power AUS Pty Ltd, Dandenong South VIC | 3.0 of 3 |
| In Australia since 2018 | 1.5 of 2 |
| Claim route: distributor or installer first, then SolaX's service team | 1.5 of 2 |
| Claim costs: freight to AUD 200 a case in some areas; AUD 150 service charge per case | 1.5 of 3 |
| Overall: 7.0 × 30% + 5.0 × 35% + 3.5 × 15% + 7.5 × 20% = 5.875, rounded to one decimal: 5.9 | |
Rubric 1.0 · scored 16 Nov 2026 · How we rate batteries · Source documents
Rated so far: 38 batteries, from 4.4 to 8.2. Compare similar batteries · Use the quote checklist
In a nutshell
What’s good
- Modular X1 Hybrid setup. X1 Hybrid can start with one master and add up to two matching slaves, subject to inverter and expansion conditions.
- Flexible mounting. Wall or floor mounting gives placement options; the manual requires a sheltered location away from direct sun.
- Modest starting size. One master gives 5.1 kWh usable at 90% depth of discharge, a modest start for evening storage.
1 more good point
- Warranty names this model. The Australian V1.6 warranty explicitly names this V2 model, with 70% capacity retention within its stated limits.
What to watch
- One master suits X1 only. One master is below the documented X3 Hybrid minimum of two cabinets, so an X3 proposal needs a different setup.
- Later expansion needs consent. After the first year, expansion needs advance SolaX consent; modular hardware doesn't guarantee unrestricted additions.
- V2 stock unconfirmed. SolaX Australia's current T58 page covers V3 only, and nothing we found confirms current V2 stock or lead time.
2 more things to watch
- Cover can end early. Ends at the earlier of 120 months after installation or 129 after manufacture, so old stock can get under ten years.
- Limit for other uses. Outside daily self-consumption and backup, a 17.9 MWh cumulative discharge limit applies; the warranty doesn't name VPPs.
Good fit for: Homes with modest evening storage needs and a SolaX X1 Hybrid inverter confirmed to support one T-BAT H 5.8 V2 master.
Look elsewhere if: You need a battery with its own AC inverter, or intend to use this single cabinet with an X3 Hybrid system.
All specifications and notes
Capacity and power
| Usable capacity | 5.1 kWhSolaX's Australian V2 datasheet (V2.9.2, now archived): battery-side usable energy at 90% depth of discharge, 0.2C and 25°C; household delivery depends on the inverter. |
|---|---|
| Battery-side rated power | 2.8 kW DCOne V2 master. The Australian datasheet also lists 4.0 kW maximum without a duration; neither figure is household AC output. |
| Inverter arrangement | X1 Hybrid: one masterThe archived Australian V2 sheet permits 1–3 cabinets on X1 Hybrid and 2–4 on X3 Hybrid, so one master is permitted on X1 only. Confirm the exact inverter generation and firmware. |
| Product warranty | Up to 10 yearsEarlier of 120 months after installation or 129 after manufacture; a specified NSW PDRS exception and separate performance limits apply. |
Manufacturer’s figures
As stated in the manufacturer’s Australian datasheet. Shown for reference; they don’t change the score.
| Weight | 72.2 kgWhether it can go on a wall, and how the installer has to handle it.One T-BAT H 5.8 V2 master cabinet |
|---|---|
| Dimensions | 474 × 193 × 708 mm (L × W × H)Whether it fits the wall or cupboard where the installer plans to put it.One T-BAT H 5.8 V2 master cabinet |
| Charge power | Rated power 2.8 kW; max power 4.0 kW (35 A max charge / discharge current)How fast it can soak up solar, or a cheap or free power window.T-BAT H 5.8 V2; max current varies with inverter model, temperature and SOC |
| Round-trip efficiency | 95%How much of the energy you store comes back out when you use it.Battery roundtrip efficiency; no conditions are printed beside the figure |
| Cell chemistry | LFPThe type of battery cell the maker says is inside.Battery type, archived AU datasheet V2.9.2 |
More specifications
| Expansion | 1–3 cabinets on X1 HybridX3 Hybrid needs 2–4 cabinets, so one master is not enough. |
|---|---|
| Enclosure | IP65, indoor or outdoorNeeds protection from direct sun and a suitable environment. |
| Operating temperature | Charge 0–55°C; discharge −10–55°CSolaX's global manual gives 5–48°C at full load. IP65 alone does not make an exposed hot wall suitable. |
| Warranty throughput | 6,000 cycles or 17.9 MWh6,000 cycles for daily self-consumption and backup; 17.9 MWh cumulative discharge for other applications. |
| Warranted accessories | EPS Box, Mate BoxAccessories SolaX's Australian warranty lists, in X1 and X3 versions; ask the installer which, if any, your backup needs. |
What the system needs
| One V2 master cabinet | The reviewed unit contains the battery and management electronics. Additional HV11550 V2 slave cabinets create larger configurations outside this review. |
|---|---|
| Compatible X1 Hybrid inverter | The battery has no household AC inverter. Confirm that the quoted X1 generation, voltage range and firmware support one V2 master. |
| Backup equipment and circuits | The installer confirms the inverter's backup hardware, AU design, circuits and output limits. SolaX's Australian warranty lists EPS Box and Mate Box accessories; ask which, if any, you need. |
One T-BAT H 5.8 V2 master cabinet provides a modest starting size for a compatible SolaX battery system. This review covers the V2 battery, with its inverter and backup equipment quoted separately.
Capacity and power
The reviewed cabinet is one T-BAT H 5.8 V2 master, without slave batteries. Its 5.8 kWh name is nominal storage. SolaX's Australian T58 datasheet V2.9.2, a file dated August 2025, lists 5.1 kWh usable at 90% depth of discharge, 0.2C and 25°C. SolaX has since put its V3 datasheet at the same web address, so the V2 sheet we rely on is an archived copy. SolaX Australia's T58 page, which still had a V2 tab when checked on 15 November 2026, has since been replaced by a product page that covers V3 only (checked 17 November 2026). The V2 tab gave 5.8 kWh total capacity, 72.2 kg and IP65, but no usable figure. Don't apply V3 features or figures to a V2 quote.
The datasheet rates one master at 2.8 kW, with 4.0 kW maximum power. It gives no duration for the maximum. Both are battery-side figures, not a guaranteed continuous AC or backup rating. Choose the inverter for the appliances you run at the same time, not just for stored energy.
Backup and installation
The V2 datasheet allows one master on an X1 Hybrid, SolaX's single-phase hybrid inverter, with up to two slaves. An X3 Hybrid, the three-phase model, needs a master and at least one slave, up to three slaves. So one master works only with the single-phase X1 Hybrid. An HV11550 V2 slave cabinet alone is not the reviewed master configuration. These are family-level arrangements: the installer still needs to confirm your exact Australian inverter generation and firmware.
Backup also needs a designed switching and circuit arrangement, which the installer specifies. SolaX's Australian warranty lists X1 and X3 EPS Box and Mate Box accessories without saying what they do, so ask the installer which, if any, your backup needs. None of this shows that this single battery can run every appliance. Have the quote specify backed-up circuits, inverter output and starting-load limits.
SolaX's global V2-era manual permits indoor or outdoor installation, but outdoors it says to avoid direct sun and humid air. The Australian datasheet's operating range is 0–55°C for charging and −10–55°C for discharging. The manual's full-load range is narrower, 5–48°C, so IP65 alone does not make an exposed hot wall suitable.
Warranty and ownership
The Australian V1.6 warranty, checked on 15 November 2026, covers products installed and activated from 1 February 2025, and its battery table names this V2 model. For products sold or installed before that date, it points to earlier warranty versions, which this review has not checked; ask SolaX which applies. Product cover ends at the earlier of 120 months after installation or 129 months after manufacture. Old stock can therefore get less than ten years after installation. Qualifying NSW PDRS installations approved by an accredited certificate provider get ten years from installation; this review does not establish eligibility.
The capacity promise is 70% retention within the same time limits. For daily self-consumption and backup, it is limited to 6,000 cycles; the warranty doesn't define a cycle. Any other application, or a mix that includes one, has a 17.9 MWh cumulative discharge limit for this model, listed beside 5.76 kWh of nominal energy. The warranty does not mention VPPs, so we treat VPP use as one of those other applications. It excludes damage caused by third-party control equipment or software that SolaX hasn't authorised in writing, so confirm how SolaX treats your VPP before joining.
Working the warranty’s energy limits through at one full charge and discharge a day:
- Home use: 6,000 cycles, about 6.0 MWh per usable kWh. At one full charge and discharge a day that is reached in about 16.4 years, so the 10-year term ends first.
- VPP and other uses: 17.9 MWh, about 3.51 MWh per usable kWh. At one full charge and discharge a day that is reached in about 9.6 years, before the 10-year term ends.
Use an authorised reseller and a SolaX- or distributor-certified installer, complete warranty registration and keep commissioning records. Report faults within four weeks, and claim within one month of the failure. The warranty treats ambient temperatures below −10°C or above 50°C as not following SolaX's instructions; the datasheet allows up to 55°C. Additions after the first year need SolaX's advance consent, and any extension must follow SolaX's battery-extension procedure.
The checked ACCC recall concerns LG S/A Gen2 batteries supplied in certain SolaX systems, rather than this Triple Power model. SolaX's November 2025 guidance separately says Triple Power was not listed for recall. Owners should identify the battery by its label, not the inverter brand.
Brand and Australian support
Support evidence checked 21 September 2026; warranty and ABR record re-read 15 November 2026. The warranty names SolaX Power AUS Pty Ltd, of Dandenong South VIC, as the Australian importer, with phone 1300 476 529 and service@solaxpower.com.au. That company has held an ABN since 25 September 2018 (checked 15 November 2026). SolaX's Australian company page and local contact page also document a local operation. A local operation doesn't tell you how claims go or how reliable the V2 is.
Claims start with the distributor that sold the battery or the installer, who contact SolaX if needed. If they can't help, or you're not satisfied, you can escalate to SolaX's service team. SolaX may change software or configuration, repair, or supply a new, refurbished or equivalent unit. In certain areas of Australia, SolaX pays normal ground freight both ways, up to AUD 200 per case; you pay any excess or other methods. The warranty also names a standard service charge of AUD 150 (excluding GST) per case, which applies once checks confirm the returned product is faulty. It doesn't name the payer outright, and SolaX must authorise any site visit first. Travel, subsistence and onsite installation or modification are excluded. A return with no fault, or one the warranty doesn't cover, lets SolaX recover labour, travel, delivery and replacement costs. Australian Consumer Law rights remain separate.
The final ARENA/ITP report covers one earlier 12.6 kWh Triple Power lab system, not this 5.8 V2 master; it cannot establish current field reliability. The known SolaX/LG recall concerns LG S/A Gen2 batteries, not this model. No T-BAT H 5.8 V2 entry appeared in the ACCC, CEC or Energy Safe Victoria searches, and no bounded V2 owner/installer sample was verified.
Price and alternatives
On 20 October 2026, no Australian manufacturer price for a complete installed V2 system was verified on the T58 product page. A price for one cabinet is a hardware price unless the offer explicitly includes the rest of the system. Start with SolaX Australia's Find an Installer directory and request an itemised V2 quote covering the master cabinet, compatible inverter, backup equipment, cabling, protection, installation, commissioning, delivery and GST. Confirm stock, manufacture date and lead time: an online V2 product section is not proof of availability.
For a fresh installation, ask for a separately specified current-generation option alongside the V2 proposal. If keeping an existing solar inverter matters, also compare an option with its own AC inverter. Use the solar battery catalogue to explore different system arrangements; obtain each alternative's exact model, warranty and complete installed price. Compare the same backup requirements and ask for the total before incentives. Check each deduction against the federal battery rebate guide; the catalogue's CEC reference does not settle exact-model or installation eligibility.
Who it suits
Use the battery size calculator to check your evening consumption against the proposed storage, then ask the installer to check essential loads against the inverter's backup rating. If expansion is likely, settle the permitted cabinet count and timing before purchase. Keep the exact battery, inverter and firmware details for any VPP enquiry. Origin's Battery Lite list named the T-BAT H 5.8 V2 when re-checked on 14 November 2026, but Origin says the battery and inverter must both qualify. Confirm your combination with each program in the SolaX VPP listings.
How it compares
Other reviewed batteries closest to 5.1 kWh of usable capacity.
- FoxESS EP5 battery reviewRated 6.6 out of 105.18 kWh usablePerformance warranty: 10 years or 19.2 MWhOne difference: VPP readinessFoxESS EP5 battery9.5T-BAT H 5.8 V23.5

- Enphase IQ Battery 5P reviewRated 6.5 out of 105 kWh usableWarranty: 15 yrs or 6,000 cyclesOne difference: WarrantyEnphase IQ Battery 5P8.0T-BAT H 5.8 V27.0

- Family reference imageEnphase IQ Battery 5P with FlexPhase reviewRated 6.8 out of 105 kWh usableWarranty: 15 years, 6,000 cyclesOne difference: FunctionalityEnphase IQ Battery 5P with FlexPhase6.5T-BAT H 5.8 V25.0

Questions people ask
Is the SolaX T-BAT H 5.8 V2 compatible with my inverter?
It has no household AC inverter and needs a compatible SolaX hybrid. SolaX's archived Australian V2 datasheet permits 1–3 cabinets on X1 Hybrid and 2–4 on X3 Hybrid, so one master suits X1 only. Confirm the exact inverter generation and firmware.
How long is the SolaX T-BAT H 5.8 V2 warranty?
Product cover ends at the earlier of 120 months after installation or 129 months after manufacture, so old stock can get less than ten years. Qualifying NSW PDRS installations are an exception, and capacity cover has separate limits.
Can I add more T-BAT H 5.8 V2 cabinets later?
Additions after the first year require SolaX's advance consent, and any addition must follow its battery-extension procedure. Settle the permitted cabinet count and timing before purchase.
Will the SolaX T-BAT H 5.8 V2 run my house in a blackout?
Only through a designed switching and circuit arrangement, which the installer specifies. SolaX's Australian warranty lists EPS Box and Mate Box accessories; ask the installer which, if any, your backup needs. None of this shows one battery can run every appliance, so have the quote state circuits and output limits.
How much does the SolaX T-BAT H 5.8 V2 cost in Australia?
On 20 October 2026 no Australian manufacturer price for a complete installed V2 system was verified on the T58 page. Installed prices come from an itemised quote for the cabinet, inverter, backup equipment and installation.
How long will 5.1 kWh last?
Divide 5.1 kWh by your average load: about 5.1 hours at 1 kW or 1.7 hours at 3 kW. The figure is battery-side; household delivery depends on the inverter.
Before you accept a quote
SolaX Power doesn’t publish a price for this battery, so the installed price comes from your quotes.
- The quote names the V2 master (not V3), the exact inverter generation and firmware, and the manufacture date.
- It confirms in writing that one master is supported on the quoted inverter; X3 Hybrid needs at least two cabinets.
- Backup hardware (which, if any, of the EPS Box and Mate Box accessories SolaX's warranty lists), circuits, output and starting-load limits are specified.
- The warranty start date and the 120/129-month limit are confirmed, along with how your VPP is treated.
- Stock and lead time are confirmed, and the cabinet, inverter, cabling, protection, installation, commissioning, delivery and GST are itemised.
Estimate the federal battery certificates for 5.1 kWh usable (opens in a new tab)
Check the model in your quote
Check that your quote names T-BAT H 5.8 V2 in the configuration this review covers. Other sizes can differ in specifications and warranty.
Other sizes in this line: T-BAT H 11.5 V2, 10.4 kWh usable · T-BAT H 17.3 V2, 15.5 kWh usable · T-BAT H 23 V2, 20.7 kWh usable
Other SolaX lines: SolaX batteries
Australian support and warranty claims
- Australian presence
- SolaX Power AUS Pty Ltd, Dandenong South VIC
- In Australia since
- 2018
- Where claims go
- Distributor or installer first, then SolaX's service team
- Claim costs
- Freight to AUD 200 a case in some areas; AUD 150 service charge per case
SolaX Power Australian contact details (opens in a new tab) · Warranty document (opens in a new tab) · Checked
VPPs that list SolaX Power Triple Power T-BAT H
Compare programsThese programs list the battery family. Your exact battery, inverter and address still need approval; inclusion does not confirm warranty cover. How VPPs work.
All programs shown require an electricity account with the provider. If you already use that retailer, a switch may not be needed; a particular plan may still be required. Credits are before electricity costs and any program fees.
2 listings · Program A–Z
| Provider | Program | States listed | Reward snapshot | Last checked |
|---|---|---|---|---|
| GloBird Energy | ZEROHERO · VPP add-on | NSW · VIC · SA · QLD (Energex) | Conditional daily and export credits | |
| Origin Energy | Loop · Battery Lite | NSW · SA · VIC · QLD · ACT | $1/kWh during VPP events |
GloBird Energy
ZEROHERO · VPP add-onListed: NSW · VIC · SA · QLD (Energex)
Origin Energy
Loop · Battery LiteListed: NSW · SA · VIC · QLD · ACT
Reward snapshots — open the program for all credits, tariffs and conditions.
Source documents
5 documents
The documents behind this rating. Where we keep a copy, it is unmodified and dated; check the manufacturer for the latest version. We work out the rating with a fixed rubric from these documents and our VPP data. No manufacturer pays for a score or sees one before it is published.
- SolaX Australia — warranty terms and conditions V1.6 (installs from 1 Feb 2025; file dated 3 Nov 2026) (PDF, opens in a new tab)
PDF, 340 KB · Used for: Warranty, Australian backing
Retrieved from au.solaxpower.com
- SolaX Australia — T-BAT H 5.8 V2 (T58) datasheet, V2.9.2, file dated Aug 2025 (archived 18 Apr 2026) (PDF, opens in a new tab)
PDF, 267 KB · Used for: Functionality, Manufacturer’s figures, Review source
Retrieved from a Wayback Machine snapshot of solaxpower.com
- au.solaxpower.com/contact-us.html (opens in a new tab)
Used for: Australian backing
- abr.business.gov.au/ABN/View?abn=69628495367 (opens in a new tab)
Used for: Australian backing
- SolaX — T-BAT H 5.8 V2 (T58) datasheet, V2.9.2, file dated 21 Oct 2026 (PDF, opens in a new tab)
PDF, 174 KB · Used for: Review source
Retrieved from au.solaxpower.com