Skip to content

Battery review · IS-BATT-21000-S1

iStore Smart Battery S1 review (IS-BATT-21000-S1)

By CompareVolt · Updated · Last full check

AI studio illustration: iStore Smart Battery S1 tower with a top power module and three battery modules.

CompareVolt rating

6.2 out of 10

20.7 kWh and up to 10.5 kW on listed iStore hybrids, but its warranty limit is unclear and no VPP we track lists it.

  • Warranty15 yrs; 28.84 MWh limit unclear
  • Functionality20.7 kWh, 10.5 kW DC; needs inverter
  • VPP readiness0 programs list iStore or the S1
  • Australian backingWA head office; partial claim costs
How this score adds up
Rubric lines and points behind this rating
Warranty 6.0 (30%)
Term: 15 years at 60% end-of-life capacity3.0 of 3
Keeps 60% at year 101.0 of 2
Home use: one 28.84 MWh figure for all three S1 sizes; per module or per stack not said1.0 of 3
Conditions: must stay on iStore monitoring; install within 31 days of purchase1.0 of 2
Functionality 7.5 (35%)
Power and backup 7.5 · 60% of Functionality
Continuous power: 10.5 kW battery DC; the inverter sets AC output3.5 of 4
Backup equipment: needs a listed iStore hybrid inverter and its backup setup1.0 of 2
Backup output: set by the inverter1.0 of 2
Three-phase homes: listed for a three-phase supply2.0 of 2
Capacity and expansion 7.0 · 30% of Functionality
Largest documented system: 20.7 kWh (3 modules in one stack; up to 4 stacks on some inverters)3.0 of 4
Adding later: more stacks in parallel; mixed capacities need iStore's approval2.0 of 4
Usable figure: 20.7 kWh, agreed2.0 of 2
Enclosure 10.0 · 10% of Functionality
Enclosure rating: IP6610.0 of 10
7.5 × 60% + 7.0 × 30% + 10.0 × 10% = 7.6, rounded to the nearest half point: 7.5
VPP readiness 0.5 (15%)
Open programs: none open0.0 of 8
Warranty room for VPP use: one 28.84 MWh figure for all three S1 sizes; per module or per stack not said0.5 of 2
Australian backing 8.5 (20%)
Presence: iStore (QLD) Pty Ltd (Solargain (Qld) until May 2024), Malaga WA3.0 of 3
In Australia since 20112.0 of 2
Claim route: iStore help desk or RMA; an accredited installer swaps the unit2.0 of 2
Claim costs: replacement and return postage; $150 swap rebate to installers, at discretion1.5 of 3
Overall: 6.0 × 30% + 7.5 × 35% + 0.5 × 15% + 8.5 × 20% = 6.2

Rubric 1.0 · scored 17 Nov 2026 · How we rate batteries · Source documents

Rated so far: 38 batteries, from 4.4 to 8.2. Compare similar batteries · Use the quote checklist

In a nutshell

What’s good

  • Up to 10.5 kW. Each module adds 3.5 kW, so the stack charges and discharges at up to 10.5 kW where the inverter allows it.
  • 15-year warranty term. Five years longer than the S0's term, though at one full cycle a day the 28.84 MWh limit ends cover first.
  • Rated at 100% DoD. iStore rates all 20.7 kWh as usable, at 100% depth of discharge.
2 more good points
  • Up to four stacks. The S1 documents allow four stacks in parallel on the 10, 15 and 25 kW three-phase iStore hybrids, with iStore's meter; get it confirmed.
  • One warranty document. The battery, iStore hybrid inverters and backup boxes share one iStore warranty document, on different terms, with claims handled by iStore in Australia.

What to watch

  • Warranty limit unclear. One 28.84 MWh figure covers all three S1 sizes, without saying if it applies per module or per stack, and only 60% of capacity is promised at end of life.
  • Inverter can cap power. iStore's datasheets cap battery discharge at about 5 to 10 kW on its single-phase hybrids and the 5, 6 and 10 kW three-phase, below the stack's 10.5 kW.
  • No VPP listing. None of the open VPP programs we track lists iStore or the S1.
2 more things to watch
  • iStore inverters only. It runs only on iStore hybrids, and iStore's lists differ: its statement names nine, the S1 manual twelve. Get your model confirmed.
  • Siting limits despite IP66. The manual asks for shelter from direct sun and rain, keeps it out of living areas and rules out outdoor sites within 500 m of the coast or prone to sea breeze.

Good fit for: A household on, or buying, a listed iStore hybrid inverter that wants about 20 kWh and up to 10.5 kW of battery power from one stack.

Look elsewhere if: You use another inverter brand, want a VPP program we track, or the only site is outdoors within 500 m of the coast or prone to sea breeze.

All specifications and notes

Capacity and power

Usable capacity20.7 kWhBattery-side usable capacity at 100% depth of discharge, 0.2C (a five-hour charge or discharge rate) and 25°C, at the beginning of life. Nominal and usable capacity are the same figure.
Battery powerUp to 10.5 kW DCRated and maximum charge and discharge for the three-module stack, 3.5 kW per module. The hybrid inverter can set a lower limit.
InverterListed iStore hybridsNine in iStore's September 2026 statement; the S1 manual adds three. The 5 and 6 kW single-phase take one stack; others two or four.
Performance warranty15 years or 28.84 MWhWhichever comes first, at 60% end-of-life capacity. One figure covers all three S1 sizes; iStore doesn't say if it applies per module or per stack.

Manufacturer’s figures

As stated in the manufacturer’s Australian datasheet. Shown for reference; they don’t change the score.

Charge power10.5 kWHow fast it can soak up solar, or a cheap or free power window.Rated/max. charge power; discharge also 10.5 kW (3.5 kW per battery module)
Noise<29 dBMatters if it sits near a bedroom or a neighbour’s window.At 1 m and typical working voltage
Cell chemistryLithium-iron phosphate (LiFePO4)The type of battery cell the maker says is inside.Cell technology

More specifications

Stack layout1 power module + 3 × 6.9 kWh modulesIS-BATT-7000-BMS on three IS-BATT-7000-ES modules. Three modules is the most one stack takes.
Size and weight590 × 255 × 1,230 mm, 216 kgWidth × depth × height of the stacked modules; the weight includes the floor-stand kit. Wall mounting is optional.
EnclosureIP66, outdoor ratedThe manual still asks for shelter from direct sun and rain, and rules out outdoor sites within 500 m of the coast or prone to sea breeze.
Expansion1, 2 or 4 stacks, by inverterOne on the 5 and 6 kW single-phase; four on the 10, 15 and 25 kW three-phase; two on every other listed iStore hybrid.
Operating temperature−20°C to +55°CThe specification notes output may be affected by temperature. A built-in heater warms a cold battery, which lowers efficiency in cold weather.
Clean Energy Council listingBAT-1085, listed to 31 Dec 2027Approved 16 September 2026; rated 10.5 kW DC with no AC output of its own.

What the system needs

Three-module battery stackOne IS-BATT-7000-BMS power module and three IS-BATT-7000-ES 6.9 kWh modules. Floor stand standard; wall mounting optional.
Listed iStore hybrid inverterAn iStore single- or three-phase hybrid that iStore lists for the S1 and confirms in writing. The inverter sets household AC output and how many stacks connect.
Backup hardware, if wantedThe S1 documents don't name it. iStore's warranty covers its single- and three-phase backup boxes; ask which your inverter needs.
Monitoring connectionThe warranty requires the battery to stay connected to iStore's monitoring platform.

The IS-BATT-21000-S1 stacks three 6.9 kWh modules under one power module and runs on a listed iStore hybrid inverter. This review covers that 20.7 kWh stack: its power, inverter fit, backup needs and warranty terms.

Capacity and power

IS-BATT-21000-S1 is one power module on three 6.9 kWh modules. iStore's August 2026 specification gives 20.7 kWh usable at 100% depth of discharge, measured at 0.2C and 25°C at the beginning of life. The IS-BATT-7000-BMS power module sits on top, and three modules is the most one stack takes. The 6.9 and 13.8 kWh stacks are outside this review.

Battery power grows with the modules: 3.5 kW each, so this stack charges and discharges at up to 10.5 kW. That is battery-side DC power, and the hybrid inverter can set a lower limit. iStore's 5 and 6 kW single-phase datasheet gives 5,000 W for battery charge and discharge. Its April 2026 single-phase datasheet gives 4,999 W discharge on the 5 kW HC, 8,000 W on the 8 kW and 9,999 W on the 10 kW. Its March 2025 three-phase datasheet gives 5,000 and 6,000 W discharge on the 5 and 6 kW models, and its 10, 15 and 25 kW three-phase datasheet, dated September 2024, gives 9,999 W on the 10 kW. That sheet gives 16.5 and 25 kW on the 15 and 25 kW models but names only S0 batteries, so confirm what those inverters allow with the S1.

The S1 is iStore's newer battery line. The Clean Energy Council listed it as BAT-1085 on 16 September 2026, and iStore's downloads page carries its specification, manual and compatibility statement. iStore's battery product page listed only the S0 on 17 November 2026. Larger systems use up to four stacks in parallel, depending on the inverter, and the specification's cover gives 82.8 kWh per inverter. Our rating counts one stack on one inverter, so it scores 20.7 kWh as the largest system.

Backup and installation

It runs only on iStore hybrids, and iStore's lists differ. Its September 2026 compatibility statement lists nine: the 5, 5 HC, 6 and 10 kW single-phase and the 5, 6, 10, 15 and 25 kW three-phase models. The S1 manual, dated 21 August 2026, also lists the 8 kW single-phase and the 5 and 10 kW HC three-phase models, and sets a minimum firmware version for every inverter. Get iStore's written confirmation for your model, and ask the installer to check its firmware. The manual's table sets the stack count: one on the 5 and 6 kW single-phase, four on the 10, 15 and 25 kW three-phase (with iStore's DTSU666-HW meter, per the specification), and two on the rest. iStore's single-phase datasheets and its March 2025 three-phase datasheet still give compatible storage as "5 kWh - 30 kWh", less than two S1 stacks, and its September 2024 datasheet for the 10, 15 and 25 kW three-phase names only S0 batteries, so have any multi-stack system confirmed in writing too.

The battery has no AC output of its own. The user manual covers backup through the inverter's off-grid switching and a backup reserve, and says not to use the batteries in backup for life-critical medical devices or similar loads. It also warns that during an automatic battery health check the charge can fall to 0%, and an outage then may cut power to loads. None of the four S1 documents names backup hardware. iStore's warranty covers its single- and three-phase backup boxes, so ask which your inverter needs, and specify the backed-up circuits and reserve in the quote.

The stack is rated IP66, and the specification recommends outdoor installation. Yet the manual asks for a sheltered site or an awning against direct sun and rain. It keeps the battery out of living areas such as bedrooms, kitchens and laundries, and rules out outdoor sites within 500 m of the coast or prone to sea breeze. In a garage it should sit clear of the drive path; the manual suggests wall mounting above bumper height. The three-module stack weighs 216 kg with its floor-stand kit. A built-in heater warms a cold battery, which lowers the system's efficiency in cold weather.

Warranty and ownership

iStore's March 2026 warranty gives the S1 15 years or 28.84 MWh, at 60% end-of-life capacity, whichever comes first. The term is five years longer than the S0's, but the end-of-life capacity is lower: the S0's is 70%. The table prints one 28.84 MWh figure against all three S1 sizes, and the document doesn't say whether it applies per module or per stack. Get iStore's answer in writing.

Working the warranty’s energy limits through at one full charge and discharge a day:

  • Energy limit: one 28.84 MWh figure for all three S1 sizes; per module or per stack not said.

The difference matters. Read per stack, 28.84 MWh is about 1,390 full charge and discharge cycles of this 20.7 kWh stack, or 3.8 years at one a day. Read per module, it is about 4,180 cycles, or 11.5 years. At one full cycle a day, either reading reaches the energy limit before the 15-year term ends.

The conditions are specific. The battery must stay connected to iStore's monitoring. Premium monitoring starts as a free trial and is offered only during the standard warranty; after that, a subscription may be payable. The battery must be installed within 31 days of purchase, and as the manual says. Faults must be reported to iStore within two weeks. Cell damage from leaving the battery uncharged or unused for long periods is excluded. iStore recommends a 15–30°C working temperature. The power module is warranted separately from the battery modules, for the term only. The same document covers iStore's hybrid inverters for 120 months and its backup boxes for 24. The document gives a start date for inverter cover but not for the battery, so keep proof of the purchase and installation dates. Australian Consumer Law rights remain.

Brand and Australian support

Support evidence checked 15 November 2026; the S1 documents, listing and support pages checked 17 November 2026. The warranty comes from iStore (QLD) Pty Ltd, which gives its head office as Malaga, Western Australia. That company's ABN has been active since 18 July 2011. Until 7 May 2024 the company was named Solargain (Qld) Pty Ltd, so the 2011 start is that company's, not the iStore name's. Its about page says it is Australian-owned and family-run, and works with suppliers on "Original Design Manufacturer products".

The S1's March 2026 safety data sheet names iStore (QLD) Pty Ltd as manufacturer and lists five factories in China that make its IS-BATT-7000-ES battery module, without saying which builds a given unit. No document we read names the cell maker. Warranty and support for this battery are iStore's.

Claims go to iStore directly. The warranty lists an email help desk, a technical support line and a warranty and RMA page, and iStore's product support page has a support form. Once a claim is confirmed, iStore ships a replacement of the "same age, type and condition", within 20 calendar days in the text and 20 business days in its service table; where it can't supply one, it may issue a credit note for the market value at the time of the claim. iStore pays the postage to return the faulty unit, which must go back within 15 business days of the replacement arriving. A CEC-accredited installer trained by iStore must fit the replacement. iStore may pay the installer a fixed $150 ex GST fee at its discretion; the document doesn't promise full labour cost, or set out a route if your installer has gone. Ask your installer what a warranty swap would cost you.

The S1 was listed in September 2026, so it has no long-term field record yet.

Price and alternatives

iStore publishes no S1 price, and its battery product page doesn't list the S1. Ask for an itemised installed quote covering the power module, three battery modules, inverter, any backup hardware, meter, electrical work, commissioning and GST.

The federal program requires a battery on the Clean Energy Council list; the S1 is BAT-1085, with a listing that runs to 31 December 2027. At 20.7 kWh, the first 14 kWh earn the full rate of the federal battery rebate and the other 6.7 kWh the 60% rate. In Western Australia, Synergy's Supported Solutions List shows eight of the nine iStore hybrids in the S1 statement, all but the 5 kW HC, with a provisional storage listing; check the complete system against the WA scheme rules. None of the open VPP programs we track lists iStore or the S1. If you want to join a VPP, get the provider's written confirmation before you buy.

iStore's earlier S0, which its product page lists, uses 5 kWh modules in stacks of up to 15 kWh, with up to 5 kW per stack and a warranty of 10 years or 18.25 MWh at 70%. The S1 manual excludes damage from using batteries of different rated capacities together without iStore's approval, so don't plan to add S1 modules to an S0 system without it in writing. These are specification differences, not a ranking; compare complete systems in the battery catalogue.

Who it suits

Estimate overnight use with the battery size calculator. If 20.7 kWh is more than you need, the 6.9 and 13.8 kWh S1 stacks give 3.5 and 7 kW. Then check the inverter: iStore's 5 and 6 kW single-phase hybrids take one stack and limit battery power to 5 kW.

Decide on backup before signing, because it means backup hardware, chosen circuits and a reserve. Confirm the site is sheltered and away from living areas before comparing quotes. Before paying, reconcile the module labels, inverter model, firmware and monitoring connection against the equipment delivered.

How it compares

Other reviewed batteries closest to 20.7 kWh of usable capacity.

See all reviewed batteries

Questions people ask

Which inverters work with the iStore S1 battery?

iStore's September 2026 compatibility statement lists nine iStore hybrids: the 5, 5 HC, 6 and 10 kW single-phase and the 5, 6, 10, 15 and 25 kW three-phase models. The S1 manual also lists the 8 kW single-phase and two HC three-phase models, so get yours confirmed in writing. Neither lists another brand.

How long is the iStore S1 battery warranty?

15 years or 28.84 MWh at 60% end-of-life capacity, whichever comes first. The table gives one figure for all three sizes without saying if it is per module or per stack, and the battery must stay connected to iStore's monitoring.

Can I add S1 modules to my iStore S0 battery?

Don't assume so. The S1 manual excludes damage from using batteries of different rated capacities together without iStore's approval, and S0 and S1 modules have different capacities. Get iStore's answer in writing.

Will the iStore S1 keep my power on in a blackout?

Only through a listed iStore hybrid inverter set up for backup. The S1 documents don't name the backup hardware, so ask which your inverter needs and which circuits it covers. The manual says not to use the batteries in backup for life-critical medical devices.

How much does the iStore S1 battery cost?

iStore publishes no S1 price. The installed price comes from an itemised quote.

How long will 20.7 kWh last?

Divide 20.7 kWh by your average load: about 21 hours at 1 kW or 7 hours at 3 kW. Inverter losses and any backup reserve reduce what reaches appliances.

Before you accept a quote

iStore doesn’t publish a price for this battery, so the installed price comes from your quotes.

  • The quote names one IS-BATT-7000-BMS power module and three IS-BATT-7000-ES modules, not S0 modules, plus the floor stand or wall bracket.
  • It names a listed iStore hybrid inverter, its firmware version and how many S1 stacks that model takes.
  • If you want blackout backup, it names the backup hardware, the circuits wired to it and the backup reserve.
  • It shows a sheltered site away from living areas, and not outdoors within 500 m of the coast or in an area prone to sea breeze.
  • iStore states in writing whether the 28.84 MWh warranty limit applies per 6.9 kWh module or to the whole stack.

Estimate the federal battery certificates for 20.7 kWh usable (opens in a new tab)

Check the model in your quote

Check that your quote names IS-BATT-21000-S1 in the configuration this review covers. Other sizes can differ in specifications and warranty.

Other sizes in this line: IS-BATT-7000-S1, 6.9 kWh usable · IS-BATT-14000-S1, 13.8 kWh usable

Other iStore lines: iStore batteries

Australian support and warranty claims

Australian presence
iStore (QLD) Pty Ltd (Solargain (Qld) until May 2024), Malaga WA
In Australia since
2011
Where claims go
iStore help desk or RMA; an accredited installer swaps the unit
Claim costs
Replacement and return postage; $150 swap rebate to installers, at discretion

iStore Australian contact details (opens in a new tab) · Warranty document (opens in a new tab) · Checked

VPPs that list iStore Battery

Your exact battery, inverter and address still need approval; inclusion does not confirm warranty cover. How VPPs work.

No open program on CompareVolt currently lists this family. This is not a provider eligibility decision. Browse all VPPs.

Source documents

4 documents

The documents behind this rating. Where we keep a copy, it is unmodified and dated; check the manufacturer for the latest version. We work out the rating with a fixed rubric from these documents and our VPP data. No manufacturer pays for a score or sees one before it is published.

Explore all solar batteries